Researchers in South Korea have developed a transparent polymer electrode that enables antimony sulfoselenide solar cells to generate electricity from both sides. Integrated into a four-terminal tandem configuration, the technology achieved a combined power conversion efficiency of 12.32%, highlighting a promising approach to next-generation thin-film photovoltaics.

Bifacial tandem solar cells: a new role for antimony sulfoselenide
Antimony sulfoselenide, with the chemical formula Sb2(S,Se)3, may not be the easiest name to remember, but the compound is steadily gaining attention in the photovoltaic industry.
The material is a thin-film semiconductor whose tunable bandgap and high optical absorption coefficient make it a promising candidate for next-generation solar cells, particularly those featuring multijunction architectures and bifacial designs.
Researchers at the Daegu Gyeongbuk Institute of Science and Technology (DGIST) in South Korea have now put the material to the test in both applications. The team developed a new transparent rear contact that enabled antimony sulfoselenide to deliver one of its strongest practical performances in a four-terminal tandem solar cell.
Why antimony sulfoselenide holds promise for solar technology
Before examining the new bifacial tandem solar cells, it is worth understanding what makes this material attractive, despite its relatively modest power conversion efficiency.
Antimony sulfoselenide has a high optical absorption coefficient, allowing it to capture sunlight with absorber layers just a few hundred nanometers thick. Its bandgap can be adjusted by changing the sulfur-to-selenium ratio, making it particularly suitable for indoor photovoltaics, semitransparent solar cells and tandem devices.
The material offers several additional advantages. Compared with established thin-film technologies such as cadmium telluride (CdTe), it has a relatively simple composition and uses elements that are generally considered less toxic, potentially supporting more uniform manufacturing and industrial scalability.
It also exhibits strong environmental stability, is insoluble in water and can be synthesized at relatively low temperatures, making it compatible with lightweight, flexible substrates.
South Korean researchers develop a transparent rear electrode
The research team set out to develop a rear contact for the Sb2(S,Se)3 solar cell that would allow light to pass through while maintaining efficient electrical charge extraction.
The challenge was to achieve both properties without relying on indium tin oxide (ITO), a widely used transparent conductive material that presents difficulties in this particular device configuration.
The solution came from organic chemistry.
Researchers engineered a transparent rear electrode consisting of two stacked polymer layers, Spiro-OMeTAD and PEDOT:PSS. By applying a solvent treatment to improve the electrical properties of PEDOT:PSS, they reduced its sheet resistance by nearly four orders of magnitude while preserving high optical transparency.
This design enables the antimony sulfoselenide solar cell to capture photons from both its front and rear surfaces.
Laboratory tests demonstrated:
- 8.2% front-side power conversion efficiency, compared with a current record of approximately 10% for the material.
- 3% rear-side power conversion efficiency.
- 9.7 mW/cm² power density under combined illumination, with one sun incident on the front and 0.3 sun on the rear.
These results demonstrate that transparent polymer contacts can support bifacial electricity generation without significantly compromising the optical properties of the absorber.
Bifacial tandem solar cells achieve 12.32% efficiency
The antimony sulfoselenide semiconductor can absorb higher- and medium-energy portions of the visible spectrum, including wavelengths extending from ultraviolet through green, yellow and orange to lighter red.
Meanwhile, it allows lower-energy light, particularly red and near-infrared wavelengths, to pass through.
To make better use of the available solar spectrum, the researchers integrated the antimony sulfoselenide device as the top cell in a four-terminal tandem architecture, pairing it with a copper indium selenide (CuInSe2) solar cell.
This configuration allows the two photovoltaic devices to convert different portions of the incoming light spectrum into electricity.
The resulting tandem system achieved a combined power conversion efficiency of 12.32% under standard testing conditions, while retaining its bifacial capabilities.
The researchers also reported a bifacial power density of 18.81 mW/cm² under one-sun illumination.
The findings point to a potential pathway for improving thin-film photovoltaic performance by combining spectral management with bifacial electricity generation.
The researchers said their work demonstrated both the feasibility of bifacial power generation using antimony-based solar cells and the potential to integrate these devices into tandem photovoltaic systems through a new transparent polymer rear electrode.
They also identified opportunities for further performance improvements, particularly by optimizing the interface between the electrode and the photoactive layer, as well as refining the device’s optical structure.
The study, Conductivity-Engineered Polymeric Rear Contacts for Bifacial Sb2(S,Se)3 Solar Cells and 4T Tandem Photovoltaics, was published in the journal Advanced Materials.











